Skip to content
TalentTECH home

Implementation guide

4 Wearable sensors for monitoring, health and injury prevention

This chapter shows how to set up wearable sensors, read the data they produce and use them in a normal training week. It covers GPS vests with motion sensors and heart-rate monitors.

Chapter 4 of 9

Also on Zenodo, with the other three videos.

4.1 Overview: what wearable sensors measure

A GPS vest holds a small unit (the electronic module) on the player's upper back. The unit combines satellite positioning (GPS) with motion sensors such as an accelerometer (often grouped as an IMU, inertial measurement unit). Satellite positioning gives distance and speed outdoors. Motion-sensor metrics, such as accelerations and impacts, can still be used indoors, where GPS is not reliable (Malone et al., 2017; Torres-Ronda et al., 2022). A chest strap measures heart rate, which shows how hard the body is working.

These numbers describe external load (what the player did) and internal load (how the body responded). For the background, see Module 3 of the TalentTECH curriculum (D2.1) and the e-learning modules (D2.2). For examples from real clubs, see Cases 2, 7 and 11 in D2.3.

4.2 Technical setup: step by step

Once, before the first session

  1. Choose a system and check its test report.

    Why: FIFA's Quality Programme for Electronic Performance and Tracking Systems (EPTS) publishes test results for tracking systems. Tested providers are listed with a public test report (FIFA, n.d.). The programme does not promote specific products (FIFA, 2022).

  2. Give each player their own numbered unit.

    Why: Units differ slightly. The same unit every session keeps a player's data comparable over time (Malone et al., 2017).

    Check: the player list in the software shows one unit per player.

  3. Enter each player's maximum heart rate from a field test agreed with your medical staff.

    Why: An age-based estimate can be wrong for an individual. A measured maximum makes heart-rate zones mean the same thing for every player (Polar, 2023).

  4. Write down your speed zones and keep them all season.

    Why: Changing zones mid-season breaks comparisons. If you use individual zones, record how you set them (Malone et al., 2017).

  5. Record the unit model and firmware version in your log.

    Why: After an update, numbers can change slightly. A dated note explains a sudden jump (Malone et al., 2017).

Before every session

  1. Charge units and straps the day before.

    Why: Follow your manual. One heart-rate system, for example, needs about 3 hours for a full charge (Polar, 2023).

  2. Create the session in the software and split it into drills.

    Why: Use the same naming pattern every time, for example date, age group, session type. Drill labels let you compare like with like (Figure 4.1).

  3. Fit the vest tightly so the unit sits on the upper back.

    Why: A loose unit bounces and adds false accelerations (Malone et al., 2017).

    Check: the unit does not move when the player jogs on the spot.

  4. Switch units on outdoors, away from buildings, and wait for satellite lock.

    Why: Waiting times differ by brand. One supplier advises 10-15 minutes; another 12 minutes the first time, then 30-60 seconds (Catapult, n.d.-a; STATSports, n.d.).

Illustrative wearable software: session setup screen A schematic software window with numbered callouts: 1 session name and type, 2 drill list, 3 player-to-device list showing device ID and battery, 4 status showing signal and sync. Team monitoring: New session SESSION 2026-11-12 U17 Training: MD-3 Type: Training Type: Match DRILLS Warm-up15 min Small-sided game 4v44 × 4 min Finishing20 min + Add drill PLAYERS AND DEVICES PlayerDevice IDBattery Player 07Unit 07 Player 11Unit 11 Player 14Unit 14Low Player 21not assigned STATUS Signal: 3 of 4 units readyLast sync: not yet synced Start recording 1 2 3 4 1 Name the session the same way every time; 2 Split it into drills; 3 One unit per player 4 Check signal and battery before you start
Figure 4.1 Session setup in typical wearable software. Illustrative interface, not a real product. Menus and names differ by supplier.

After every session

  1. Download the data and check signal quality.

    Why: Most software shows satellite count and a precision value (HDOP). Mark sessions with poor signal and do not compare them with normal sessions (Malone et al., 2017; Catapult, n.d.-b).

  2. Label indoor sessions as "indoor".

    Why: GPS distance and speed are not reliable indoors. Use only motion-sensor metrics or heart rate there (Torres-Ronda et al., 2022).

  3. Ask each player for a session-RPE rating.

    Why: Ask "How hard was the whole session?" (0-10) and multiply by the minutes, for example 4 × 87 = 348 arbitrary units. Teach players the scale before you start using it (Haddad et al., 2017).

  4. Put units back on charge and store the data under the agreed access rules.

    Why: Only named staff should see the data (see Annex C).

4.3 Interpreting wearable data

Wearable numbers are estimates with a margin of error (Torres-Ronda et al., 2022). Use them to plan and adjust training, with five rules in mind.

  1. Compare like with like. Do not compare numbers from different brands or systems, or from broadcast match tracking and your training vests, as if they were the same (Malone et al., 2017).
  2. Know what a "score" means. Before you use a brand's own load score, ask the supplier how it is calculated (Torres-Ronda et al., 2022).
  3. Read youth data in context. Interpret load in relation to each player's age, growth stage and fitness (Torres-Ronda et al., 2022).
  4. Check plan against reality. Compare the planned intensity (easy, medium, hard) with what players report. A large gap is a reason to talk, not to sanction (Haddad et al., 2017).
  5. Do not treat numbers as injury forecasts. Load monitoring helps you plan training. It cannot reliably tell you which player will be injured, so expect false alarms and missed cases (Bahr, 2016).

4.4 Using wearables in the training week

  • Same routine every time. Charge, fit, lock, record, download and check signal in the same order (section 4.2). A fixed routine reduces missing data.
  • Send a short report soon after the session. Give a few key numbers per player and one clear message (Torres-Ronda et al., 2022).
  • Name one data owner. This person downloads, checks and shares the data. Name a second person as backup.
  • Link it to the plan. Use the numbers when you plan the next sessions, not only when you review the last one. Chapter 7 shows a sample weekly cycle for all tools together.

4.5 Troubleshooting

Table 4.1 Common wearable problems and what to do
ProblemLikely causeWhat to do
Distance and speed missing or far too lowNo satellite lock, or the session ran with an indoor profileCheck the session profile (Polar, n.d.). Next time, switch units on outdoors and wait for lock (step 9).
Numbers look odd for one sessionPoor satellite signal near stands or buildingsLook at the signal-quality indicators (Catapult, n.d.-b). Mark the session and leave it out of comparisons.
Heart-rate strap shows no signalDry electrodes, loose strap or lost Bluetooth pairingWet the electrodes, tighten the strap, check it is the right way round, check Bluetooth, then pair it again (Polar, n.d.).
Sudden change in all players' numbersFirmware or software update, or a changed speed-zone settingCheck your log for the update date and the zone settings (steps 4-5). Do not compare across the change without a note.
One player's data does not match their effortWrong unit or loose vestCheck the unit number against the player list and check the fit (steps 2 and 8).
Unit runs out during the sessionNot charged, or battery ageingCharge the day before (step 6). Replace units that repeatedly fail.

4.6 Quick-start checklist by role

Coach

  • Plan intensity (easy, medium, hard) for each drill.
  • Agree drill names with the data owner.
  • Use the short report when planning the next session.

Scout

  • Use physical data only from the same system and season.
  • Read youth data in light of age and growth stage.
  • Never rank players on one physical number alone.

Performance staff

  • Keep the unit list, zones and firmware log up to date.
  • Check signal quality after every session.
  • Collect session-RPE from every player after each session.

Academy manager

  • Confirm the data protection check (Annex C) is complete.
  • Name a data owner and a backup.
  • Budget for charging, spare vests and replacement units.

The implementation guide is published under a CC BY-SA 4.0 licence.